Tuesday, October 9, 2012

Twisted Infinity Scarf by SEWspirational


Here we go...it sure has been awhile!  This is my Twisted Infinity Scarf which can be worn two different ways!

View One...
Twisted Infinity Scarf by SEWspirational

View Two...
Twisted Infinity Scarf by SEWspirational

It's a tutorial...yippee!  Let's begin.  You will need:

1/2 yard each of two different fabrics.  
The wilder and more opposing the prints are from one another, the better!

  • First...use your rotary cutter and straighten the (fabric shop) cut edges so that your 1/2 yard fabric pieces are square and straight.  
  • Open up your fabric pieces.  They will now measure approximately 18" wide (which will be straight of grain) x 44" long (going WOF).
  • The length will need to be trimmed so that it measures 37" long.  
  • Trim this excess length by measuring up from and KEEPING the non-printed selvage edge of each piece, which is to be included in your 37" length measurement.   
  • Trim away the excess length (approximately 7 inches) from the PRINTED selvage edge.  
  • This will make more sense later.


Now fold your fabric pieces in half lengthwise with right sides together.  Stitch a scant 1/4" seam along the length of your pieces to create a fabric tube. 


Press open your scant 1/4" seam.  Pull through the fabric for each tube so that they are right sides out.  

With right sides out, press your seams so that they are on one side of each fabric tube.  Your fabric tubes should measure approximately 8 3/4" wide x 37" long.


Grab four pieces of paper (or some stickies) and label them A, B, C and D.



Lay your pressed fabric tubes on a flat surface. 

Pin the A and C paper to the end of the tube with the factory selvage. >>> THIS IS REALLY IMPORTANT!  And have these ends on your LEFT!  (*Refer to Diagram 1 below.)
  

Pin the B and D paper to the opposing ends.  These ends should be on your RIGHT!


*Refer to the diagram below for paper placements.


Ok...we're almost ready for the FUN part...gulp...this is where we start getting twisted!


To create the Twisted Infinity follow the steps and photos.  
You will find each instructional step is listed below the photo image 
and the steps are preceded with an asterik *

*STEP 1... Lay the A/D piece over the B/C piece.
*STEP 2... Pull part of the A/D piece under the B/C piece.
*STEP 3... Flip the A/D piece over the B/C piece again.
*STEP 4...Slide A towards B keeping the fabric pieces flat on your surface.
*STEP 5...Slide C towards D keeping the fabric pieces flat on your surface. 

*STEP 6...Slip the B edge inside of the A edge about 3/4" 
and pin in place.  
NOTE:  You will notice in this step that you are placing the raw edge of B inside A, which has the factory selvage edge and which will become a finished edge with this step.

*STEP 7...Slip the D edge inside of the C edge about 3/4" 
and pin in place.
*STEP 8...Stitch to close up each end of your fabric tubes, 
A to B and C to D. 

*********************************

So here in this image you can see I chose to use a zigzag stitch to close up my ends.
Choose your style of stitching here...it's all good!


Hooray...here is your completed Twisted Infinity Scarf which now looks....TWISTY!!  
Ooooh...how fun is this!


Of course...now you need to figure out how to WEAR 
your new scarf but hey, it's all fun!



I hope you will try my Twisted Infinity Scarf.  It took me a looooog time to figure out the twist.  I love the results.  I think you will too!


All Rights Reserved
This tutorial, images and instructions are the Copyright Property of SEWspirational.  If you use any of my images, you must link back to my blog and this tutorial.  You may not rewrite nor adapt and reproduce this pattern in any form.  You may not copy and post this tutorial anywhere.  

You may use this tutorial to make a Twisted Infinity Scarf for personal use, gift giving, or for small craft show venues.  
You may not take credit for the Twisted Infinity Scarf as your pattern creation.
All reference to the origination of this pattern must be credited to myself as SEWspirational. 
This pattern may not be reproduced nor sold.  
This pattern may not be used by any corporation in any form or production.

2 comments:

  1. That is really clever, Linda!
    Judith.

    ReplyDelete
    Replies
    1. Thanks Judith. I had quite a time figuring it out, but it's really cute on the wearer! : )

      Delete